Skip to Content
BerryAlloc · Wall&Water

Waterproof bathroom walls. No tiles, no grout.

Wall&Water are large wall panels of 60 by 240 cm with a decorative high-pressure laminate surface. They click together with watertight joints and often go straight over the existing tiles: a new shower wall without breaking anything out.

60 × 240 cm

per panel, floor to ceiling

29

decors

7

designs, from allover to tile look

Lifetime

warranty for residential use

What is Wall&Water?

A complete wall system for wet rooms

Wall&Water is the bathroom panel of BerryAlloc, the Belgian maker of laminate, vinyl and wood floors. Each panel is 60 cm wide and 240 cm high, so one panel covers a standard wall from floor to ceiling without a horizontal joint.

The panels click together. The joint between two panels and the aluminium or white profiles at the start, the corners and the end of the wall make the wall watertight. Sealant finishes the bottom, the corners and the openings for taps and pipes.

That makes Wall&Water a real alternative to tiles: no tile adhesive, no grout lines that discolour, and in many renovations no breaking out of the old tiles.

Watertight

Click joint and profiles keep the water out, also in the shower.

No grout lines

One smooth surface: easy to clean, no mould in the joints.

Quick to install

Glue on a flat wall or screw to a wooden frame. No drying time for tile adhesive or grout.

Over old tiles

On a flat, sound tiled wall: no demolition, no dust, no extra waste.

UV resistant

The decor keeps its colour, also in a bright bathroom.

Up to 3 m high

For higher ceilings an extension panel of 62 cm goes on top.

Designs

29 decors, 7 designs

Every decor comes in one or more designs. The design decides whether you see one calm surface or the look of tiles or wooden slats. The grooves of a tile design are part of the decor: there is nothing to grout.

Allover

The whole panel is one surface, without a joint pattern. Calm and very easy to clean.

Tile 60×30, 60×60, 60×120

The look of a tiled wall in three sizes, with the grooves in the decor.

Quattro and Slat

The oak decors as slats (Slat) or as a pattern of four planks (Quattro): warm, in a wet room.

Moroccan

A small decorative tile pattern, for an accent wall or a niche.

Finishes: S · smooth BR · brushed GF · gloss finish
Where to use it

For every wall that gets wet

Shower walls

Walk-in shower or shower tray: the panels go down to the tray or the floor, finished with sealant.

Around the bath

From the edge of the bath to the ceiling, without a single grout line.

Whole bathroom

All walls in one decor, or one accent wall in a tile or wood design.

Kitchen wall

Behind the worktop: one smooth surface for splashes and grease.

Toilet and utility room

Hygienic and easy to keep clean.

Projects

Holiday homes, care homes, hotels: quick renovation with little downtime.

Not for saunas, steam rooms or right next to a heat source. In doubt about your wall or your room? Ask us before you order.

Compared

Wall&Water, tiles or SPC wall panels?

All three have their place. This is how they differ in a bathroom.

Wall&WaterCeramic tilesSPC wall panels
Grout linesNoneMany, they need maintenanceFew
Over existing tilesYes, on a flat and sound wallUsually broken out firstYes, on a flat and sound wall
InstallationLarge panels, glued or screwed, no drying timeAdhesive, tiles and grout: several daysClick panels, glued
Panel size60 × 240 cm, floor to ceilingPer tileDepends on the range
Profiles and sealingComplete system: base, start, corner and end profilesTile trims and siliconeTrims and sealant
Best forShowers and bathrooms that must be done quickly and stay easy to cleanClassic tiled look, floors and walls in one materialBudget renovation of walls with a stone or marble look
The system

Five profiles finish every wall

The profiles make the wall watertight at the bottom, the edges and the corners. The visible profiles come in aluminium and in white. The numbers are the same as in the calculator below.

1

Base profile

At the bottom of the wall, on the floor or the shower tray. The panels stand in it.

Count: the calculator does it for you, from the wall length.

2

Start U profile

The side where you start, against a door frame or a wall without panels.

Count: 1 per side where you start.

3

Inner corner

Where two panelled walls meet, like the back corner of a shower. Visible as a profile, or hidden behind the panels.

Count: 1 per inner corner.

4

Outer corner

A corner that points into the room: a boxed-in pipe, a wall that sticks out, the end of a niche.

Count: 1 per outer corner.

5

Start / end L profile

Every other free side of a panel: where the panels stop, next to the shower door, at a window.

Count: 1 per free side. At the ceiling: wall length ÷ 2.4, rounded up.

On a solid wall

Panel adhesive and 45 mm screws. The wall must be flat, dry and sound: plaster, concrete, plasterboard or existing tiles.

On a wooden frame

30 mm screws, no adhesive. For walls that are not flat, or when pipes have to go behind the panels.

Sealant

In light grey or white, for the base profile, the corners and the openings for taps and pipes.

Finishing

Cleaning wipes and Wall Pro Cleaner to remove sealant and dirt, and a tapping block to click the panels together without damage.

Examples

Which profiles? Four bathrooms, seen from above

Find the situation that looks like yours, count the numbers and fill them in. One profile is as high as a panel: you count one per corner or free side, from floor to ceiling.

Existing wall Wall&Water panels Shower tray or bath Profile, with its number

Shower in a corner

Two walls of 1.2 m and 0.9 m. The walls meet in one inner corner; the panels stop at two free sides, next to the shower door.

  • Wall length 2.1 m
  • 3 inner corner: 1
  • 5 L profile: 2
Calculate this example

Shower between three walls

A niche of 0.9 + 1.2 + 0.9 m. Two inner corners at the back; the two side walls each stop at a free side at the front.

  • Wall length 3 m
  • 3 inner corners: 2
  • 5 L profiles: 2
Calculate this example

One wall behind the bath

Only the back wall of 1.7 m, from side wall to side wall. The side walls get no panels: a U profile where you start, an L profile where you stop.

  • Wall length 1.7 m
  • 2 U profile: 1
  • 5 L profile: 1
Calculate this example

Wall with a boxed-in part

0.9 m of wall, then a part that comes forward (0.6 m deep) and 0.6 m along its front. One inner corner, one outer corner, a start and an end.

  • Wall length 2.1 m
  • 2 U profile: 1
  • 3 inner corner: 1
  • 4 outer corner: 1
  • 5 L profile: 1
Calculate this example

Counting in three rules

  1. Walk along the panels with your finger. Every corner pointing away from you is an inner corner (3), every corner pointing towards you an outer corner (4).
  2. Every side where the panels stop gets a finishing profile: a U profile (2) where you start or an L profile (5).
  3. No visible profile in the corner? Count that corner as a hidden inner corner instead of a visible one.
Calculator

How many panels and profiles do you need?

Enter the length of the walls you want to cover and count the corners. The calculator gives panels, profiles, adhesive, sealant and screws, with a link to every product.

Your walls

Add up the widths of all walls you cover. One panel covers 60 cm of wall, 240 cm high.

Installation
Profiles and corners (number)

Not sure? See the four examples above. The base profiles are counted from the wall length.

Colour of the visible profiles
Colour of the sealant

Your shopping list

Enter the wall length to see what you need.

Total excl. VAT

This is an estimate. Check the quantities for your project and the installation instructions of BerryAlloc; cutting and openings can call for an extra panel.

Installation

Installation in four steps

  1. Prepare the wallFlat, dry and sound, or a level wooden frame. Measure the walls and mark pipes and taps.
  2. Base profileFix the base profile on the floor or the shower tray, perfectly level: it sets the line for the whole wall.
  3. PanelsCut to size, glue or screw the first panel and click the next ones in, with the tapping block.
  4. FinishCorner and end profiles, then sealant at the bottom, in the corners and around every opening.
Questions

Frequently asked questions

Can I install Wall&Water over my old tiles?

Yes, when the tiled wall is flat, sound and clean, and no tiles are loose or hollow. If the wall is not flat, a wooden frame is the better choice.

Is a shower wall with Wall&Water really watertight?

Yes, when it is installed with the profiles and the sealant as BerryAlloc prescribes: the click joint, the base profile on the floor or tray and sealant in the corners and around every opening.

Do I need adhesive and screws?

On a solid wall you glue the panels and fix the profiles with 45 mm screws. On a wooden frame you screw everything with 30 mm screws and need no adhesive. The calculator adapts to your choice.

My ceiling is higher than 2.4 m. What now?

For walls up to 3 m an extension panel of 60 × 62 cm goes on top of each panel, with 3 m profiles. Tick the option in the calculator; not every decor has an extension panel yet, we tell you which ones.

How do I make holes for taps and the shower head?

Drill with a hole saw slightly larger than the pipe and seal the edge with sealant. Measure carefully before you glue the panel.

How do I clean the panels?

With a soft cloth and a mild cleaner, or Wall Pro Cleaner. No scouring products: they dull the surface.

Where can I see the decors?

In our showroom you can see and touch the panels. Scan the QR code at a sample to open this page with that decor already chosen in the calculator.

Planning a bathroom with Wall&Water?

We check your measurements and the right profiles with you, and make a quotation with everything you need.