![youtube - [Video]](/web/image/product.image/10014/image_128/youtube%20-%20%5BVideo%5D?unique=2a15630)
Staal Osmo 3044 Hardwax-Olie Raw Look 5ml
| Brand | Osmo |
| Droogtijden | 24 uur |
| Uithardingstijd | 2 weken |
| Minimaal aantal lagen | 2 |
| Verwerkingstijd | 0.5 uur |
| Overschilderbaar na | 24 uur |
| Bevat pigmenten | Ja |
| Schuren tussen lagen | Nee |
| Schrobbestendig | Ja |
| Krasbestendig | Ja |
| Vlekbestendig | Ja |
| Opslagtijd | 5 jaren |
| Type oppervlak | Hout |
Description
Natural look with Osmo 3044 Raw
Osmo Raw 3044 is a transparent, matt wood finish that uniquely combines the benefits of natural oils and waxes in one product. Osmo Hardwax-Oil Effect Raw is stain-resistant, water-repellent and hard-wearing, and results in a surface that feels pleasant. 3044 gives the wood a matt, untreated look. Hardwax-Oil Raw contains a small amount of white pigment, so the wood does not look as if it has been wetted. After treatment with this product, we advise finishing the second coat with Osmo Hardwax-Oil Original. This gives complete treatment and protection of the surface, while keeping the enhancement of your wooden surface almost invisible.
Osmo Hardwax-Oil Raw 3044 contains slightly less white pigment than Osmo Hardwax-Oil Effect Natural 3041, so the surface becomes slightly less light than with an Osmo 3041 treatment.
1. Stir the product well for 2 minutes. After opening the tin, the oil and wax are separated. Always test on the surface first to check that the result has the desired effect.
2. Apply the first coat of Hardwax-Oil Effect very thinly with a roller or floor brush to the new or sanded wood. Make sure the product is rolled out well, otherwise the surface will show lap marks. Make sure every part of the wood is covered with the product.
3. Mistakes made during application can be corrected on the wet surface up to 30 minutes afterwards, such as roller marks or brush hairs.
4. Drying of the first coat takes about 24 hours (at 23 °C and 50% relative humidity). At lower temperatures or higher humidity, drying takes longer. Always ensure good ventilation, with windows and doors open.
5. If desired, the dried coat can be lightly sanded with fine sandpaper (400 grit) or a scotch pad.
6. Apply the second finishing coat thinly with Hardwax-Oil Original Clear, also with the Osmo microfibre roller or floor brush.
7. Drying of the second coat in approx. 8-12 hours; see point 4.
1. Stir the product well for 2 minutes. After opening the tin, the oil and wax are separated. Always test on the surface first to check that the result has the desired effect.
2. Buff the first coat of 3041 onto the new or sanded wood with a white pad or lint-free cloth, along the wood grain.
3. Within 20 minutes, buff the Hardwax-Oil Natural dry with the fleece pad or a lint-free cloth, also along the wood grain. This ensures an even look and prevents too much product being applied.
4. Mistakes made during application can be corrected on the wet surface up to 30 minutes afterwards, such as roller marks or brush hairs.
5. Drying of the first coat takes about 8-10 hours (at 23 °C and 50% relative humidity). At lower temperatures or higher humidity, drying takes longer. Always ensure good ventilation, with windows and doors open.
6. Apply the second and third finishing coats thinly with Hardwax-Oil Original Clear, using the Osmo microfibre roller or floor brush.
7. Drying of Hardwax-Oil Original Clear takes about 8-10 hours.
If you buff the surface, apply two more coats of Hardwax-Oil Original Clear to protect the wood. Buffing one coat of Hardwax-Oil Natural 3044 applies less white pigment, so the wood will be less light in colour.